We use cookies to make your experience better. To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
Walther Blenheim Full Depth Convector Gas Fire
- 4.0kW Heat Output (Gross)
- Open Fronted Gas Fire
- 3 Year Guarantee
Walther Full Depth Convector Inset Gas Fire
- Full depth convector showcases beautiful flame picture
- Requires a min. fireplace depth of 250mm (+ 20mm debris collection)
- Instant 4.0kW heat output (Gross)
- Open fronted for increased realism
- OVERVIEW: Impressive full depth convector gas fire with fantastic flame picture designed for deep fireplace openings
The Walther is a full depth convector inset gas fire designed to fit homes with a larger class 1 or 2 pre-fabricated flue system (min. 127mm or 5" diameter) or conventional class 1 brick chimney. It features a clever heat exchanger that provides convected heat in addition to standard radiant heat. The full depth convector platform uses the same deep burner tray as its full depth radiant counterpart. This signifies that the Walther also produces a stunning flame picture and under bed glow from it's deep fuel bed.
It is important to note that all this technology does come with a trade-off. Despite fitting most fireplace openings, typically 16" wide x 22" high (please refer to product specification - excludes low lintels) the Walther's full depth convector firebox is much larger than other models and requires a minimum of 250mm plus 20mm for debris collection. This can limit its options where installation is concerned and therefore it is important to check its compatibility with the destined fireplace opening.
The Walther is available with coal, pebble or log effect fuel bed, and can be specified in Manual Control (Rotary), Manual (Fingerslide) or Remote Control.
The Blenheim fret is a classic traditional cast design with ornate vertical bars and delicate form. It features a bowed profile with two decorative finials and is designed to free stand in front of the fire and frame. The Blenheim fret is available in: brass (solid brass), brass & black (solid brass), chrome (chrome plated brass), chrome & black (lightweight aluminium), black (lightweight aluminium). The ashpan is a separate component and if applicable, provides access to the controls (model dependent). The one-piece frame is held in position with magnets (supplied) and is available in either: brass effect, chrome effect or black.
Please note the price is dependent upon the final configuration. Natural gas only.
This information is intended for guidance only. Superior Fires recommends booking a Home Survey to determine the actual chimney or flue specification.
Model Identifier | Conventional Full Depth Inset Convector Heater Gas Category/Pressure = I2H(20) |
---|---|
Heat Input Gross (High) | 6.8kW |
Heat Input Gross (Low) | 3.5kW |
Heat Output Gross (High) | 4.0kW |
Heat Output Gross (Low) | 2.1kW |
Direct Heat Output | 3.2kW |
Heat Type | Radiant & Convected Heat |
Chimney Flue Compatibility | Pre-Fabricated - Class 2 (127mm/5" Diameter), Conventional Chimney - Class 1 (178mm/7" Diameter or Greater) |
Control Ignition | Battery-Free Piezo Spark Ignition (Manual - Rotary Control), Battery Spark Ignition (Manual - Fingerslide Control), Battery Spark Ignition (Remote Control) |
Control Location | Low Level - Front - Behind Ash Pan (Manual - Rotary Control), High Level - Right - Side (Manual - Fingerslide Control), Handset (Remote Control) |
Air Vent Required | Not Required |
Manufacturer Guarantee | 3 Years |
Safety Features | Flame & Oxygen Monitoring Device |
Installation Requirement | Gas Safe Registered Installer (Bord Gais - ROI) |
Installation Information | As with any open fire, a fire guard complying with BS 8423 must be used. Fire guards are intended to protect people from falling into a fire, prevent burns and reduce the risk of injury, particularly to young children and the infirm. In addition it is intended to reduce the risk of fire resulting from clothing and/or other flammable materials coming into contact with, or in proximity to, burning fuel and/or hot surfaces. |
Fuel Type | Natural Gas |
Fire Type | Open Fronted |
Installation Type | Inset |
Engine Type | Full Depth Convector |
Width Outline A | 480mm |
Height Outline B | 595mm |
Depth Outline C | 250mm |
Rear Width Min D1 | 380mm |
Rear Width Max D2 | 380mm |
Rear Height E | 545mm |
Opening Width Min X1 | 380mm |
Opening Width Max X2 | 450mm |
Opening Height Min Y1 | 540mm |
Opening Height Max Y2 | 575mm |
Opening Depth Min Z | 270mm |
Packaging Width | 575mm |
Packaging Height | 670mm |
Packaging Depth | 360mm |
Packaging Weight | 22.0kg |
Rebate Depth | 250mm |