Regent Farlam Electric Fireplace Suite

In stock
Item No:
  • 43" Painted White Fireplace Surround
  • 37" x 37" Black MDF Back Panel
  • 48" Black MDF Hearth
  • ERP Electric Fire
Manuals/PDF's Details Specifications Reviews

Regent Farlam Electric Fireplace Suite

  • Includes Fireplace Surround, Back panel, Hearth and Electric Fire

The Regent Farlam Electric fireplace suite is features a traditional wooden surround, back panel, hearth and an electric fire. The surround, back panel and hearth are made using a stable MDF core base and are painted. The surround in finished in white gloss and the back, panel and hearth is finished in satin black.

The Farlam LED inset electric fire is a fully compliant ERP fire and features LED technology designed to significantly improve the flame picture and running performance. LED technology not only provides a deeper, richer flame picture with enhanced flame movement but is also a fraction of the cost to run when compared to a conventional incandescent bulb. It will last a lot longer too.

The inset electric fire features a 2.0kW heat output, flame effect only setting – no heat, thermostatic control, timer control, full remote control or buttons on the front of the fire below the canopy. A helpful LED display is located in the top left hand corner of the window which displays, flame brightness, timer, thermostatic control and a moulded plastic coal effect fuel bed.  A discrete fan heater provides forward directional heat and is of good quality to reduce operating noise. The Clara fits a standard fireplace opening, typically 16" wide x 22" high (please refer to specification).

For added convenience two spacer frames are provided (supplied fitted) to allow the Clara to be taken out of the box, placed flush against a flat wall and plugged in for instant heat - no chimney or flue depth required. For installation into a fireplace opening, one or both spacer frames can be removed (depending on the available fireplace depth). This provides the following options: fully inset (0 spacers - requires a 114mm fireplace depth), semi-inset (1 spacer fitted - requires a 54mm fireplace depth) or flush-fit (2 spacers - 0mm fireplace depth).

The Farlam fret design features vertical bars which compliments contemporary, modern or traditional home decors. The Farlam fret is available in: brass (solid brass) It is designed to free stand in front of the fire and frame. The ashpan is a separate component and provides access to the controls (model dependent). The one-piece frame is held in position with magnets (supplied) and depending on the model is available in: brass effect.

Your fireplace suite is made up of a number of different components and it is important to ensure that your installer not only meets the required qualifications and requirements, but that they have all the necessary experience to fit ALL the components. Superior Fires recommends the fitting fireplaces suite to be undertaken by a competent fitter or installer. 

This information is intended for guidance only. Superior Fires recommends booking a Home Survey to determine whether this appliance is compatible with your requirements. All installations must be carried out in accordance with the requirements set out in the Building Regulation documents, in particular, Approved Document J. There are independent bodies which have been approved to carry out installations in accordance with these regulations.

Please note that assembly is required and that these products are NOT suitable for GAS products.

Batteries are not included with the fire

More Information
Heat Input Gross (High) 2.0kW
Heat Input Gross (Low) 1.0kW
Heat Output Gross (High) 2.0kW
Heat Output Gross (Low) 1.0kW
Heat Type Fan Heater
Chimney Flue Compatibility No Chimney or Flue Required
Control Location High Level - Front - Below Canopy (Manual - Buttons) & Remote Control
Air Vent Required Not Required
Manufacturer Guarantee 3 Years
Safety Features Thermal Trip Switch
Installation Requirement Qualified Electrician Recommended
Installation Information All electric fires feature an automatic safety cut-out device. Simply plug into a standard socket. No chimney or flue required. Designed for use in Great Britain and Republic of Ireland only. All fires must be installed in accordance with the manufacturer’s installation and user instructions and current Building Regulations.
Heat Direction Frontwards
Technology Low energy LED flame effect
Power Voltage Supply 220 - 240V
Colour White
Control Type Manual - Button & Remote Control
Fuel Type Electric
Engine Type LED
Size Option/s 43"
Width Outline A 1100mm (43")
Height Outline B 1022mm
Depth Outline C 185mm
Cutout Width H 420mm
Cutout Height I 570mm
Internal Width D 740mm
Internal Height E 803mm
Leg Width F 1030mm
Hearth Width J 1220mm (48")
Hearth Height K 50mm (2")
Hearth Depth L 380mm (15")
Mantle Width 43
Rebate Depth 25mm (1") / 75mm (3")
Write a Review
Your Rating